Disk/Video Interface: Cable: Difference between revisions

From Tandy Tech
Jump to navigation Jump to search
 
(45 intermediate revisions by the same user not shown)
Line 1: Line 1:
Special cable for Disk/Video Interface
Special cable for Disk/Video Interface
=3-part cable kit supporting all models 100, 102, 200=
https://photos.app.goo.gl/Jy1hXhc3aSbkcaFr6
[[File:DVI_cable_kit.jpg|thumb]]


===For Model 100===
This is the best way to make a cable.
* It supports all models 100, 102, and 200.
* All plugs that can be polarity-keyed, and/or strain-relieved, are. (The DIP40 on the underside of a Model 100 is neither polarity-keyed nor strain-relieved, but there is at least a pull-handle to avoid pulling on the cable itself.
* Assembly does not require twisting 20 pairs of wires and somehow crimping them all in a perfect row like a ribbon. All crimps are normal and easy with a small hobby vice.
 
==To build one yourself==
https://github.com/bkw777/TRS-80_Disk_Video_Interface_Cable
 
: Part 1: Ordinary 40 pin ribbon cable with female idc connectors with strain relief clips on both ends, about 20 inches.
:: You can also buy cables like this part pre-made in various lengths for less than the cost of the individual parts.
 
: Part 2: "Twist adapter": https://oshpark.com/shared_projects/EoeBHp2k
:: Or just solder the two male 40-pin connectors directly back to back with no pcb. The PCB is just to make it a little easier.
:: Make sure the pin 1 mark on both connectors are on the same end, so that pin 1 of one connector goes to pin 2 of the other connector. 
:: The polarity notches should be on opposite sides from each other, NOT the same side.
 
: Part 3: Model 100 adapter cable - 8 inch 40 pin ribbon cable with female idc & strain relief on one end, and a DIP40 idc on the other end.
:: No twists in the wires like in many of the pics for other cable types below. just a regular flat crimp.
:: Take 8 inches of 3/8" (or 1/2" if you can find any) strong fabric ribbon and glue both ends to the underside of the DIP40 connector between the pins, in a closed loop.
:: Both gluing the ribbon in a closed loop, and gluing to the connector, are important to prevent the connector from tipping and bending the pins during extraction.
 
: See these pics for reference: https://photos.app.goo.gl/3TmJLMhK1WJ23mr4A
 
: Model 100 needs all 3 parts
: Models 102 and 200 only need parts 1 & 2
 
==To buy one==
:https://www.arcadeshopper.com/wp/?page_id=11#!/Disk-Video-Interface-cable-kit-for-Models-100-102-200/p/141211030/category=28313042
 
=Cable supporting model 100 only=
Parts:
Parts:
*40pin DIP idc connector
*40pin DIP idc connector
:http://www.king-cart.com/phoenixent/product_name=HWS15322
:https://www.peconnectors.com/index.php?p=catalog&mode=search&search_str=HWS15322
*40pin female idc connector, with polarity notch and strain-relief
*40pin female idc connector, with polarity notch and strain-relief
:http://www.king-cart.com/phoenixent/product_name=HWS1877
:https://www.peconnectors.com/index.php?p=catalog&mode=search&search_str=HWS1877
*40pin ribbon cable, 20 inches
*40pin ribbon cable, 20 inches
:http://www.king-cart.com/phoenixent/product_name=HWS16014
:https://www.peconnectors.com/index.php?p=catalog&mode=search&search_str=HWS16014


Assembly:
Assembly:
:https://photos.app.goo.gl/kmBbz9Vn8MpAwtMi7
*Crimp the cable in the DIP connector such that if you are looking at the dip connector with the #1 pin top-left and pins pointing away from you, the cable exits to the right, red stripe on top.
*Crimp the cable in the DIP connector such that if you are looking at the dip connector with the #1 pin top-left and pins pointing away from you, the cable exits to the right, red stripe on top.
*For the DVI end of the cable...
*For the DVI end of the cable...
**This assumes you ordered the actual DIP connector linked above, or have another one that connects it's pins to the conductors in the same pattern. Not all do. See note below.
**This assumes you ordered the actual DIP connector linked above, or have another one that connects it's pins to the conductors in the same pattern. Not all do. See note below.
**Grab the red wire and the one next to it as a single pair, and peel the pair away from the rest of the cable for about 2 to 3 inches. Repeat for the rest of wires, so the cable ends in 20 loose pairs.
**Grab the red wire and the one next to it as a single pair, and peel the pair away from the rest of the cable for about 2 to 3 inches. Repeat for the rest of wires, so the cable ends in 20 loose pairs.
**Take a sacrificial IDC connector, with strain relief clip, all snapped together but with no cable, so that the connector makes a thin open slot that's the perfect size for a cable to fit in. This will be used as a wire guide to hold all the loose pairs into their original flat ribbon cable shape so that you can crimp them all in a connector.
**Take the 1st pair of wires (the one with the red stripe), and twist it 1/2 way so the wires are reversed. Insert this pair into the IDC connector in the 1st 2 wire positions at the pin 1 end of the connector. Hold this pair in place by holding a light pressure on the idc connector, enough to keep the wires from falling out, but not enough to prevent you from inserting tbe next pair of wires.
**Take the 1st pair of wires with the red wire, twist the pair 1/2 way, and insert it into the empty slot, right against one end of the slot, so that there is a grey wire at the edge of the slot, and the red wire is one position in from the end of the slot. Repeat the twist & insert for all the remaining pairs, until the whole cable is in the slot, but with every pair twisted.
**Repeate this process for the next pair of wires, and all the rest.
**Crimp a new female IDC connector on the end of the cable. Make sure the triangle marker for pin-1 is on the red-stripe side of the cable. Wiggle the bundle of cables around a little to settle all those loose pairs into their proper positions before really crimping. It doesn't matter much which way the polarty notch points. There is room for the cable to fold back over the connector under the DVI if it needs to. What matters is that the pin-1 marker is on the same side of the cable as the red wire.
**When all 20 pairs are inserted, Wiggle the cable alotle while applying light pressure on the idc connector to settle all the pairs into perfect alignment before crimping.
**Crimp. (I use a small table top hobby vice. Have the jaws open just enough for the connector to fit. While maintaining pressure on the connector to hold all the wores in place, slide one end of the connector into the jaws, and tighten the jaws untill the connector is stiff but still able to slide the rest of the way into the jaws. You want the vice to take over the job of keeping enough pressure on the wires so they don't fall out. Slide the connector the rest of the way into the vice. Check the wires one last time, wilggle, push pull as necessary so they are all in position and none of the pairs is shorter or longer than the others. Then tighten the jaws to crimp the connector all the way.)
**Fold the wires over the back of the connector and add the strain relief clip to the crimped connector.


[[File:m100_dvi_cable_1.jpg|200px]]
[[File:m100_dvi_cable_1.jpg|200px]]
Line 29: Line 65:


====NOTES====
====NOTES====
*This pinout flatly violates the pinout written in the Service Manual for the DVI! Never the less, this is the way it actually needs to be wired.


*Most DIP IDC connectors connect pin 1 to conductor 2, and pin 40 to conductor 1. This is almost guaranteed to be the only iind you can get today. For instance:
*Most DIP IDC connectors connect wire 1 to pin 40, and wire 2 to pin 1. This is almost guaranteed to be the only kind you can get today. For instance:
:[https://photos.app.goo.gl/UhRHhuOCz3DtfZl83 Various makes of DIP IDC connectors]
:[https://photos.app.goo.gl/UhRHhuOCz3DtfZl83 Various makes of DIP IDC connectors]
:All of these connectors require twisting every 2 wires in the cable.
:All of these connectors require twisting every 2 wires in the cable.
:But the original cable from Tandy had a special versiin of the connector where pin 1 connected to conductor 1 and pin 2 to conductor 40. That special connector doesn't need any twists in the ribbon cable.
:But at least one version of the original cable from Tandy had a special version of the connector where wire 1 connected to pin 1, and wire 2 connected to pin 40. That special connector doesn't need any twists in the ribbon cable.
:It's theoretically possible you might find that kind of connector, in which case you should not split and twist the wires.
:It's theoretically possible you might find that kind of connector, in which case you should not split and twist the wires.


Line 40: Line 75:
:http://ebay.com/itm/182240437070
:http://ebay.com/itm/182240437070


===For Model 102===
=Cable that supports Model 102 only=
Parts:
Parts:
*40pin boxed male idc connector, with polarity notch
*40pin boxed male idc connector, with polarity notch
:http://www.king-cart.com/phoenixent/product_name=HWS15924
:https://www.peconnectors.com/index.php?p=catalog&mode=search&search_str=HWS15924


*40pin female idc connector, with polarity notch and strain-relief
*40pin female idc connector, with polarity notch and strain-relief
:http://www.king-cart.com/phoenixent/product_name=HWS1877
:https://www.peconnectors.com/index.php?p=catalog&mode=search&search_str=HWS1877


*40pin ribbon cable, 20 inches
*40pin ribbon cable, 20 inches
:http://www.king-cart.com/phoenixent/product_name=HWS16014
:https://www.peconnectors.com/index.php?p=catalog&mode=search&search_str=HWS16014


Assembly:
Assembly:
Line 70: Line 105:
[https://photos.app.goo.gl/rJI6McVf9jRmI7Is2 More Pictures]
[https://photos.app.goo.gl/rJI6McVf9jRmI7Is2 More Pictures]


===For Model 200===
=Cable supporting models 102 and 200 only=
There are a few different ways to do this.
 
====Original/Official Cable for Tandy 102 and 200====
The actual original cable for Model 102 & 200 looked like this on the computer end. You can't get exactly that size of connector today in a crimp-on form. The only kind of crimp-on male shrouded idc connector you can get today is longer, and fits in a Model 102, but does not fit in a Model 200.
 
[[File:T200_DVI_Cable_Original_Plug_1.jpg|200px]]
 
====Good Cable====
Here is one method to make a good cable that:
*Doesn't require splitting the ribbon cable up into 20 pairs and twisting each pair.
*Includes a shroud around the male pins that actually fits in the system bus connector opening in a Model 200.
*Is polarity-keyed on both ends.
 
The down-sides are:
*Have to solder two parts together, and it's a little fiddly & annoying to solder two sets of plain pins to each other, and work in the small gap between the two plastic parts.
*There is no strain-relief for the crimped connection on the computer end of the cable, so pulling on the cable to unplug it from the computer will weaken or break the contact between the wires and the pins in the crimp-on connector. This is adressed by adding a pull-handle, so it's ok as long as you always use the pull-handle.
 
Pay attention to the orientation of the red stripe when crimping, consult the pictures below. The red stripe goes with the pin 1 mark on both the female IDC connector and on the boxed male header connector.
 
Soldering the two connectors back-to-back takes the place of having to twist every pair of wires.
 
DigiKey parts order: http://www.digikey.com/short/jhqvwf
 
Step 1: Solder the "wire-to-board" aka "transition" connector back to back to the boxed male header connector.
 
Step 2: Hold the soldered assembly with the polarity notch up, male pins pointing away from you, so you are looking at the back of the crimp connector. Place the cable in the crimp connector with the cut end up and the red stripe to the left (red stripe goes with the pin 1 mark on the boxed male header connector). Crimp the cable.
 
Step 3: Make a pull handle for the computer end of the cable by feeding a double loop of heavy fishing line the long way between the two rows of soldered pins between the two soldered connectors. Use enough line to make a double loop large enough to put 2 or 3 fingers inside the loop. Tie the ends together. Trim the excess line ends to within 1/4" of the knot. Melt the cut ends down to the know and melt the knot a little too.
 
Step 4: Crimp the female idc connector with strain relief on the other end of the cable, red stripe on the pin 1 mark.
 
[[File:T200_DVI_Cable_01a.jpg|200px]]
[[File:T200_DVI_Cable_02a.jpg|200px]]
[[File:T200_DVI_Cable_03a.jpg|200px]]
[[File:T200_DVI_Cable_04a.jpg|200px]]
[[File:T200_DVI_Cable_05a.jpg|200px]]
[[File:T200_DVI_Cable_06a.jpg|200px]]
[[File:T200_DVI_Cable_07a.jpg|200px]]
[[File:T200_DVI_Cable_08a.jpg|200px]]
[[File:T200_DVI_Cable_09a.jpg|200px]]
[[File:T200_DVI_Cable_10a.jpg|200px]]
[[File:T200_DVI_Cable_11a.jpg|200px]]
[[File:T200_DVI_Cable_12a.jpg|200px]]
[[File:T200_DVI_Cable_13a.jpg|200px]]
 
====Easy Cable====
The simplest way to make a working cable for Model 102 or 200 is to use a cable with female IDC connectors on both ends (most ordinary IDE cables work), and then add a [http://www.ebay.com/itm/272898119517 gender-changer male pin header] to the computer end.
 
This is not ideal, because the resulting assembly is not polarity keyed or shrouded. It allows the cable to be plugged in backwards or upside down, or offset by one row, and the male pins are not protected from shorting or bending.


The Model 200 needs the same wiring as the 102, but the boxed male idc connector for the 102 above does not fit in the Model 200.
But it's very simple to put together, especially if you use an ordinary IDE cable, you don't even have to crimp the connectors yourself. Just buy the pin header and stick it in any common pre-made IDE cable.


The simplest way to make a working cable for 200 is to use a cable with female IDC connectors on both ends (most ordinary IDE cables work), and then add a [http://www.ebay.com/itm/272898119517 gender-changer male pin header] to the computer end.
You should glue the pin header in to the IDE cable, just a tiny bit of super-glue on the black plastic parts, try not to let it run into the metal parts. This is so that when you un-plug the cable from the computer, the pins stay with the cable instead of staying in the computer.


This is not ideal, because the resulting assembly is not polarity keyed, and the male pins are not protected from shorting or bending, and the pin header sometimes stays in the computer when you remove the cable instead of coming out with the cable, requiring you to pry it out with something.
'''This cable is not polarity keyed. Pay attention to the orientation of the red stripe in these pictures. It's up to you to plug it in the right way and never get it backwards by mistake!'''


But it's very simple to put together, especially if you use an ordinary IDE cable, you don't even have to crimp the connectors yourself. Just buy the pin header and stick it in any common pre-made IDE cable. And, this cable works on Model 102 exactly the same as Model 200.
Also for the IDE cable, watch out for some cables that won't work.
* Use a 40-wire cable not 80-wire
* Some IDE cables have a pin missing, or plugged. You need a cable with all 40 pins.
* Some IDE cables have a small hole punched in the middle of the cable to cut one of the wires. Pin 20 is sometimes a power-delivery wire, and some ide devices might not like that, so some cables break that wire to be safe. It looks like a tiny oval hole punched in the cable. They are not common but they do exist, and so you need to just look and make sure you don't use a cable like that.


[[File:T200_DVI_Cable_1.jpg|200px]]
[[File:T200_DVI_Cable_1.jpg|200px]]
Line 89: Line 176:
[https://photos.app.goo.gl/beTUKxXHDnvlLg083 More Pictures for Model 102/200 Easy Cable]
[https://photos.app.goo.gl/beTUKxXHDnvlLg083 More Pictures for Model 102/200 Easy Cable]


The actual original cable for Model 102 & 200 looked like this on the computer end. You can't get this thin close shroud on a crimp-on connector today, only pcb solder.
===Quick-n-Dirty neat trick===
Another way to get the wires crossed the right way (instead of that tedious and finnicky peeling & twisting 20 pairs), is just join 2 ordinary female idc connectors with a double ended male-male idc pin header. The arrangement of the connectors matters, and the rule is just match up the red stripe from both cables. Thanks Mike Stein for this trick.


[[File:T200_DVI_Cable_Original_Plug_1.jpg|200px]]
What this means exactly is, to use this trick:
 
*To make a cable for Model 100:
===Quick-n-Dirty neat trick===
:*Make 2 cables. One with a DIP IDC on one-end and a regular female IDC on the other end, and another with regular female IDC connectors on both ends. Orient the red stripes on both cables with the Pin #1 marks on all connectors. Crimp all connectors on normally, with no twists in the wires anywhere. Join the two cables with a single double-sided pin header, keeping the red stripes from both cables aligned. This creates a working cable, where the double-sided straight-through pin header joining the two female connectors face-to-face ends up having the same effect as twisting the pairs of wires.
Another much easier way to get the wires crossed the right way (instead of that tedious and finnicky peeling & twisting 20 pairs), is just join 2 ordinary female idc connectors with a double ended male-male idc pin header. The arrangement of the connectors matters, and the rule is just match up the red stripe from both cables. For 102 & 200, you can dispense with one cable and use the 200 cable above. Thanks Mike Stein for this trick.
*To make a cable for Model 102 and 200:
:*Same as the 3-part cable above for Model 100, except omit the cable with the DIP IDC on it, and just keep the cable with two regular female IDC connectors and the double-sided pin header. Simply take the cable with the two regular female IDC connectors and the double-sided pin-header, and plug the double-sided pin header right in to the 102 or 200. Pay attention to the orientation of the red stripe. The cable should stay in the same orientation as it comes out from under the DVI, as if it layed flat the whole way to the computer. The red stripe should be towards the side of the computer with the power switch. This is actually exactly the same as the "Easy Cable" above.


http://www.ebay.com/itm/272898119517
http://www.ebay.com/itm/272898119517


[[File:flip-pairs-idc-cable-trick.jpg|200px]]
[[File:flip-pairs-idc-cable-trick.jpg|200px]]

Latest revision as of 03:25, 16 October 2023

Special cable for Disk/Video Interface

3-part cable kit supporting all models 100, 102, 200

https://photos.app.goo.gl/Jy1hXhc3aSbkcaFr6

This is the best way to make a cable.

  • It supports all models 100, 102, and 200.
  • All plugs that can be polarity-keyed, and/or strain-relieved, are. (The DIP40 on the underside of a Model 100 is neither polarity-keyed nor strain-relieved, but there is at least a pull-handle to avoid pulling on the cable itself.
  • Assembly does not require twisting 20 pairs of wires and somehow crimping them all in a perfect row like a ribbon. All crimps are normal and easy with a small hobby vice.

To build one yourself

https://github.com/bkw777/TRS-80_Disk_Video_Interface_Cable

Part 1: Ordinary 40 pin ribbon cable with female idc connectors with strain relief clips on both ends, about 20 inches.
You can also buy cables like this part pre-made in various lengths for less than the cost of the individual parts.
Part 2: "Twist adapter": https://oshpark.com/shared_projects/EoeBHp2k
Or just solder the two male 40-pin connectors directly back to back with no pcb. The PCB is just to make it a little easier.
Make sure the pin 1 mark on both connectors are on the same end, so that pin 1 of one connector goes to pin 2 of the other connector.
The polarity notches should be on opposite sides from each other, NOT the same side.
Part 3: Model 100 adapter cable - 8 inch 40 pin ribbon cable with female idc & strain relief on one end, and a DIP40 idc on the other end.
No twists in the wires like in many of the pics for other cable types below. just a regular flat crimp.
Take 8 inches of 3/8" (or 1/2" if you can find any) strong fabric ribbon and glue both ends to the underside of the DIP40 connector between the pins, in a closed loop.
Both gluing the ribbon in a closed loop, and gluing to the connector, are important to prevent the connector from tipping and bending the pins during extraction.
See these pics for reference: https://photos.app.goo.gl/3TmJLMhK1WJ23mr4A
Model 100 needs all 3 parts
Models 102 and 200 only need parts 1 & 2

To buy one

https://www.arcadeshopper.com/wp/?page_id=11#!/Disk-Video-Interface-cable-kit-for-Models-100-102-200/p/141211030/category=28313042

Cable supporting model 100 only

Parts:

  • 40pin DIP idc connector
https://www.peconnectors.com/index.php?p=catalog&mode=search&search_str=HWS15322
  • 40pin female idc connector, with polarity notch and strain-relief
https://www.peconnectors.com/index.php?p=catalog&mode=search&search_str=HWS1877
  • 40pin ribbon cable, 20 inches
https://www.peconnectors.com/index.php?p=catalog&mode=search&search_str=HWS16014

Assembly:

https://photos.app.goo.gl/kmBbz9Vn8MpAwtMi7
  • Crimp the cable in the DIP connector such that if you are looking at the dip connector with the #1 pin top-left and pins pointing away from you, the cable exits to the right, red stripe on top.
  • For the DVI end of the cable...
    • This assumes you ordered the actual DIP connector linked above, or have another one that connects it's pins to the conductors in the same pattern. Not all do. See note below.
    • Grab the red wire and the one next to it as a single pair, and peel the pair away from the rest of the cable for about 2 to 3 inches. Repeat for the rest of wires, so the cable ends in 20 loose pairs.
    • Take the 1st pair of wires (the one with the red stripe), and twist it 1/2 way so the wires are reversed. Insert this pair into the IDC connector in the 1st 2 wire positions at the pin 1 end of the connector. Hold this pair in place by holding a light pressure on the idc connector, enough to keep the wires from falling out, but not enough to prevent you from inserting tbe next pair of wires.
    • Repeate this process for the next pair of wires, and all the rest.
    • When all 20 pairs are inserted, Wiggle the cable alotle while applying light pressure on the idc connector to settle all the pairs into perfect alignment before crimping.
    • Crimp. (I use a small table top hobby vice. Have the jaws open just enough for the connector to fit. While maintaining pressure on the connector to hold all the wores in place, slide one end of the connector into the jaws, and tighten the jaws untill the connector is stiff but still able to slide the rest of the way into the jaws. You want the vice to take over the job of keeping enough pressure on the wires so they don't fall out. Slide the connector the rest of the way into the vice. Check the wires one last time, wilggle, push pull as necessary so they are all in position and none of the pairs is shorter or longer than the others. Then tighten the jaws to crimp the connector all the way.)
    • Fold the wires over the back of the connector and add the strain relief clip to the crimped connector.

More Pictures

NOTES

  • Most DIP IDC connectors connect wire 1 to pin 40, and wire 2 to pin 1. This is almost guaranteed to be the only kind you can get today. For instance:
Various makes of DIP IDC connectors
All of these connectors require twisting every 2 wires in the cable.
But at least one version of the original cable from Tandy had a special version of the connector where wire 1 connected to pin 1, and wire 2 connected to pin 40. That special connector doesn't need any twists in the ribbon cable.
It's theoretically possible you might find that kind of connector, in which case you should not split and twist the wires.
  • More sources for crimp-on dip40 plugs
http://ebay.com/itm/182240437070

Cable that supports Model 102 only

Parts:

  • 40pin boxed male idc connector, with polarity notch
https://www.peconnectors.com/index.php?p=catalog&mode=search&search_str=HWS15924
  • 40pin female idc connector, with polarity notch and strain-relief
https://www.peconnectors.com/index.php?p=catalog&mode=search&search_str=HWS1877
  • 40pin ribbon cable, 20 inches
https://www.peconnectors.com/index.php?p=catalog&mode=search&search_str=HWS16014

Assembly:

  • Crimp the male connector on one end of the cable. Make sure the red wire goes on the Pin-1 marker on the connector, and ideally put the polarity notch at the end of the cable.
  • On the other end of the cable, same as for the DVI-end above for Model 100.
(TODO: Make a new cable and update pics reflecting the following notes.)
Note: These pictures show the wires twisted on the computer end instead of the DVI end. It actually doesn't make a difference where you put the twists, electrically. But it's better to put the twists on the DVI end for a few reasons. The twisted end of the cable is weaker, because the wires have been seperated from each other, making it more likely for individual pairs to have their connections weakened from pulling.
  • Neater looking. The twists are hidden under the DVI.
  • The DVI end suffers a less flexing than the computer end, because the computer moves around more than the DVI, and the computer end of the cable is handled more than the DVI end.
  • The female connector on the DVI end has a strain relief clip.
  • The socket in the DVI has latches that eject the connector out without having to pull on the cable.

More Pictures

Cable supporting models 102 and 200 only

There are a few different ways to do this.

Original/Official Cable for Tandy 102 and 200

The actual original cable for Model 102 & 200 looked like this on the computer end. You can't get exactly that size of connector today in a crimp-on form. The only kind of crimp-on male shrouded idc connector you can get today is longer, and fits in a Model 102, but does not fit in a Model 200.

Good Cable

Here is one method to make a good cable that:

  • Doesn't require splitting the ribbon cable up into 20 pairs and twisting each pair.
  • Includes a shroud around the male pins that actually fits in the system bus connector opening in a Model 200.
  • Is polarity-keyed on both ends.

The down-sides are:

  • Have to solder two parts together, and it's a little fiddly & annoying to solder two sets of plain pins to each other, and work in the small gap between the two plastic parts.
  • There is no strain-relief for the crimped connection on the computer end of the cable, so pulling on the cable to unplug it from the computer will weaken or break the contact between the wires and the pins in the crimp-on connector. This is adressed by adding a pull-handle, so it's ok as long as you always use the pull-handle.

Pay attention to the orientation of the red stripe when crimping, consult the pictures below. The red stripe goes with the pin 1 mark on both the female IDC connector and on the boxed male header connector.

Soldering the two connectors back-to-back takes the place of having to twist every pair of wires.

DigiKey parts order: http://www.digikey.com/short/jhqvwf

Step 1: Solder the "wire-to-board" aka "transition" connector back to back to the boxed male header connector.

Step 2: Hold the soldered assembly with the polarity notch up, male pins pointing away from you, so you are looking at the back of the crimp connector. Place the cable in the crimp connector with the cut end up and the red stripe to the left (red stripe goes with the pin 1 mark on the boxed male header connector). Crimp the cable.

Step 3: Make a pull handle for the computer end of the cable by feeding a double loop of heavy fishing line the long way between the two rows of soldered pins between the two soldered connectors. Use enough line to make a double loop large enough to put 2 or 3 fingers inside the loop. Tie the ends together. Trim the excess line ends to within 1/4" of the knot. Melt the cut ends down to the know and melt the knot a little too.

Step 4: Crimp the female idc connector with strain relief on the other end of the cable, red stripe on the pin 1 mark.

Easy Cable

The simplest way to make a working cable for Model 102 or 200 is to use a cable with female IDC connectors on both ends (most ordinary IDE cables work), and then add a gender-changer male pin header to the computer end.

This is not ideal, because the resulting assembly is not polarity keyed or shrouded. It allows the cable to be plugged in backwards or upside down, or offset by one row, and the male pins are not protected from shorting or bending.

But it's very simple to put together, especially if you use an ordinary IDE cable, you don't even have to crimp the connectors yourself. Just buy the pin header and stick it in any common pre-made IDE cable.

You should glue the pin header in to the IDE cable, just a tiny bit of super-glue on the black plastic parts, try not to let it run into the metal parts. This is so that when you un-plug the cable from the computer, the pins stay with the cable instead of staying in the computer.

This cable is not polarity keyed. Pay attention to the orientation of the red stripe in these pictures. It's up to you to plug it in the right way and never get it backwards by mistake!

Also for the IDE cable, watch out for some cables that won't work.

  • Use a 40-wire cable not 80-wire
  • Some IDE cables have a pin missing, or plugged. You need a cable with all 40 pins.
  • Some IDE cables have a small hole punched in the middle of the cable to cut one of the wires. Pin 20 is sometimes a power-delivery wire, and some ide devices might not like that, so some cables break that wire to be safe. It looks like a tiny oval hole punched in the cable. They are not common but they do exist, and so you need to just look and make sure you don't use a cable like that.

More Pictures for Model 102/200 Easy Cable

Quick-n-Dirty neat trick

Another way to get the wires crossed the right way (instead of that tedious and finnicky peeling & twisting 20 pairs), is just join 2 ordinary female idc connectors with a double ended male-male idc pin header. The arrangement of the connectors matters, and the rule is just match up the red stripe from both cables. Thanks Mike Stein for this trick.

What this means exactly is, to use this trick:

  • To make a cable for Model 100:
  • Make 2 cables. One with a DIP IDC on one-end and a regular female IDC on the other end, and another with regular female IDC connectors on both ends. Orient the red stripes on both cables with the Pin #1 marks on all connectors. Crimp all connectors on normally, with no twists in the wires anywhere. Join the two cables with a single double-sided pin header, keeping the red stripes from both cables aligned. This creates a working cable, where the double-sided straight-through pin header joining the two female connectors face-to-face ends up having the same effect as twisting the pairs of wires.
  • To make a cable for Model 102 and 200:
  • Same as the 3-part cable above for Model 100, except omit the cable with the DIP IDC on it, and just keep the cable with two regular female IDC connectors and the double-sided pin header. Simply take the cable with the two regular female IDC connectors and the double-sided pin-header, and plug the double-sided pin header right in to the 102 or 200. Pay attention to the orientation of the red stripe. The cable should stay in the same orientation as it comes out from under the DVI, as if it layed flat the whole way to the computer. The red stripe should be towards the side of the computer with the power switch. This is actually exactly the same as the "Easy Cable" above.

http://www.ebay.com/itm/272898119517