TPDD

Overview

There were two versions of the Tandy Portable Disk Drive. Both were very similar. The drive is a a re-branded Brother FB-100.

Common features of both versions

Size, shape, weight

Batteris: 4 x AA

Wall power: 5.5mm x 2.1mm, 6vdc, center negative, 400ma (Tandy 26-3804)

Media: 3.5" DD, aka "720K" diskettes (not HD 1.44M)

Drive is single-sided. The disks may be single or double-sided, but the drive only uses one side.

Tandy Portable Disk Drive

100K

TPDD bootstrap procedure

TPDD Operation Manual

Command Reference

Software Manual

Tandy Portable Disk Drive 2

200K in the form of 2 100K banks (still only uses one side of the disk)

TPDD-2 bootstrap procedure

TPDD-2 Operation Manual

Parts

Belt

Standard size code: FRW-8.5

Search "FRW 8.5 belt" on Google or ebay

Cable

Pinout

+------------------------------------------------+
|                                                |
|                                                |
|                 RS-232C                        |
|                   ___                          |
|               +--+   +--+              +-----+ |     
|               | 7 5 3 1 |              | (o) | |
|               | 8 6 4 2 |              |     | |
|               +---------+              +-----+ |
+------------------------------------------------+

1 GND

2 CTS

3 DTR

4 RTS

5 DSR

6 TXD

7 RXD

8 NC

In the beginning, there was the Marty Goodman Document, and it was good.

More recently, Rick Shear has taken a new and very careful look at a real cable, and the Marty Goodman doc, and has probably identified the "mystery" components that Marty Goodman talks about. It looks right, and this cable does indeed work.

Rick's Initial post

Rick's Follow-up

Rick's PCB

Since then I have made my own pcb using the same key transistor, but in a smaller pcb which fits more types of back shells and leaves more room for cord strain relief, and the pads for the db25 plug are longer and spaced more accurately to work with a plug that has through-hole solder pins instead of solder cups, so the PCB actually fits in between the rows of pins.

Here are all the parts to build the cable:

• Circuit Board (updated version not shown in these pics)
• Components

OSHPark sends 3 boards. If you want to use all 3 boards and build 3 cables, multiply all quantities in the DigiKey cart by 3.

DigiKey web site is sometimes pretty glitchey. If it says invalid part numbers, just reload the page.

• The numbers 1-7 on the PCB correspond to the numbers on the TPDD connector in the diagram above. Pin 8 on the TPDD is not used.
• You need a SN-28B Crimp Tool.
• Additional materials:

3/16" heat shrink tubing

1/2" heat shrink tubing (double wall, 3:1 ratio)

These photos show Rick's original PCB, not the new one, but it works the same way.

• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 
• 

Cable BKW 1

Re-work of Rick's pcb:

• smaller pcb to allow more room to strain-relieve the cable end inside the back shell, and assure compatbility with more types of backshells.
• fewer, shorter, simpler traces and vias
• adjusted footprint for db25 plug to use a through-hole solder type instead of solder cup type, so the pcb actually fits between the pins. That type has longer pins so the solder pads needed to be lengthened.

• 
• 
• 

Cable BKW 2

New design with the transistors on the TPDD-end instead of the DB25-end. This way you do not need to crimp Dupont style pins. You just assemble this tiny pcb, cut the 9-pin plug off of a cheap pre-made 9/25 modem cable and throw it away, and solder the cable with factory molded 25 pin plug to this pcb, and finally secure with some hot-glue & heat-shrink, maybe a zip-tie. This uses the same transistor as the two other versions above. Still working on an answer for polarity. Probably replace the single 2x4 header with a 2x3 header standing up, and two 1x2 headers to either side of that.

• 
• 
• 
• 
• 
• 
• 
• 

Cable BKW 3

The through holes for the wires were way too small and close in BKW2.

• 
• 
• 
• 

Cable BKW 4

Adds a place to secure the cable with a zip tie.

PCB: https://oshpark.com/shared_projects/dyMZxoye

BOM: https://www.digikey.com/short/pbc3pp

• 
• 
• 
• 

Software

For PCs

TPDD used double density 3.5" disks, but used a format that is incompatible with modern pc drive controllers. Normal MS-DOS formatted disks are written with MFM encoding, while the TPDD used FM encoding. Even using special software to read non-standard formats, you can't make a normal drive & drive controller read or write FM.

To read or write a TPDD disk from a modern machine, you need a working TPDD drive and the special RS232-to-TTL level-shifting serial cable that came with it, and a "TPDD Client" software to talk to the drive over the serial connection the same way the M100 does.

There are several TPDD clients for more modern machines. Most of these are themselves also no longer modern. For example Lap-Desk and PDD are both 16-bit DOS programs that don't work on Windows.

TpddTool Python TPDD Client

For M100/102/200

The normal way to use a TPDD is to install a "dos" on an M100. Several such dos's have been made. The drive came with a utility disk and a functional dos called "floppy". Others have been made by 3rd parties that provided more features or smaller ram footprint or more flexible installation/usage. There are also various special purpose utility programs aside from dos's.