Disk/Video Interface: Drives: Difference between revisions
No edit summary |
|||
| (2 intermediate revisions by the same user not shown) | |||
| Line 9: | Line 9: | ||
In general, the simplest way to search for a compatible drive is to search for "360K" drives. | In general, the simplest way to search for a compatible drive is to search for "360K" drives. | ||
Most 1.2M drives won't work. A 360K drive has the right TPI & Density, but | Most 1.2M drives won't work. A 360K drive has the right TPI & Density matching the original 180K drive, but has two sides instead of just one. The extra side is simply not used by the DVI. It's technically a waste, but there are no half-height 180K drives out there to be found, while 360K drives are still relatively easy to find. | ||
A few known working drives | A few known working drives | ||
| Line 33: | Line 33: | ||
To use some non-original drives in a DVI, you may have two choices: | To use some non-original drives in a DVI, you may have two choices: | ||
* Drill new holes in the upper drive bay brackets. | * Drill new holes in the upper drive bay brackets. | ||
* Only use the new drive in the lower drive bay | :or | ||
* Only use the new drive in the lower drive bay and leave the original drive in the upper bay. | |||
===Cabling & Configuration=== | ===Cabling & Configuration=== | ||
If using 2 drives | If using 2 drives: | ||
Drive 0: | Drive 0: | ||
:Install terminator resistor | :Install terminator resistor | ||
:Jumper DS0 (Or DS1 if the Drive Select jumpers start at 1 instead of 0) | :Jumper DS0 (Or DS1 if the Drive Select jumpers start at 1 instead of 0) | ||
: | :Lower bay in DVI | ||
:End of cable connector | :End of cable connector | ||
Drive 1: | |||
:Remove terminator resistor | :Remove terminator resistor | ||
:Jumper DS1 (or DS2 if the Drive Select jumpers start at 1 instead of 0) | :Jumper DS1 (or DS2 if the Drive Select jumpers start at 1 instead of 0) | ||
: | :Upper bay in DVI | ||
:Middle of cable connector | :Middle of cable connector | ||
:Ground wire, if it can reach, otherwise cover end of ground wire with electrical tape. | :Ground wire, if it can reach, otherwise cover end of ground wire with electrical tape. | ||
Latest revision as of 17:09, 28 April 2018
Disk/Video Interface Compatible Floppy Drives
Specs:
- 5.25" half-height
- 180KB
- 48TPI
- Double Density
- Single Side
In general, the simplest way to search for a compatible drive is to search for "360K" drives. Most 1.2M drives won't work. A 360K drive has the right TPI & Density matching the original 180K drive, but has two sides instead of just one. The extra side is simply not used by the DVI. It's technically a waste, but there are no half-height 180K drives out there to be found, while 360K drives are still relatively easy to find.
A few known working drives
| Make | Model | Notes |
|---|---|---|
| TEC | FB-501 | Original Drive |
| Epson | SD-521 | Side Mounting Holes |
| Panasonic | JU-455-5 | Side Mounting Holes |
| Teac | FD-55B-01-U |
Mounting Holes
There are two common locations for screw holes on the sides of half-height drives. Usually drive mounting brackets will have 4 holes on each side to allow for both types of drives.
The brackets for the upper drive bay in the DVI only have one set of holes, which matches the original drive, and some other drives do not have screw holes in that location.
The lower drive bay uses screw holes on the bottom of the drive, not the sides, so any drive works in the bottom bay.
To use some non-original drives in a DVI, you may have two choices:
- Drill new holes in the upper drive bay brackets.
- or
- Only use the new drive in the lower drive bay and leave the original drive in the upper bay.
Cabling & Configuration
If using 2 drives:
Drive 0:
- Install terminator resistor
- Jumper DS0 (Or DS1 if the Drive Select jumpers start at 1 instead of 0)
- Lower bay in DVI
- End of cable connector
Drive 1:
- Remove terminator resistor
- Jumper DS1 (or DS2 if the Drive Select jumpers start at 1 instead of 0)
- Upper bay in DVI
- Middle of cable connector
- Ground wire, if it can reach, otherwise cover end of ground wire with electrical tape.